• [00:01:34] <charliex> if i look on pin 8 of u10 that should show something coming in if its all hooked up
  • [00:02:59] <jkridner> k, then turn around from the Beagle Hospital should be pretty fast. Make sure to get an RMA# before sending it back.
  • [00:03:03] * banderson (n=irc@69.71.183.7) Quit (Read error: 110 (Connection timed out))
  • [00:03:45] * guillaum1 (n=Guillaum@AMontsouris-153-1-28-4.w86-212.abo.wanadoo.fr) has left #beagle
  • [00:04:19] * guillaum11 (n=gl@AMontsouris-153-1-28-4.w86-212.abo.wanadoo.fr) has joined #beagle
  • [00:05:20] * guillaum11 is now known as guillaum1
  • [00:08:59] * odesus (n=Omar@201.165.118.65) has joined #beagle
  • [00:11:14] <kholz> So has anyone here gotten dsplink going?
  • [00:11:39] <kholz> I'd like to do a phase vocoder using beagle.
  • [00:12:43] <charliex> i'll keep checking just in case its a wiring goof.
  • [00:18:57] <kholz> Which rev are you on? I thought I saw something about an issue on the elinux wiki page that sounds just like that.
  • [00:19:05] <kholz> rather, which rev is your board, charliex
  • [00:20:40] <kholz> http://elinux.org/BeagleBoard#Errata and errata #8
  • [00:26:14] <charliex> my fault, wiring problem. didn't help that i had just read that thread on the serial board failures, i used an idc to db9 from a pc, its wired differently i had swapped 2 and 3 for the null modem, but the beagle is a different wiring.
  • [00:27:06] <mru> the beagle is wired same as most PCs
  • [00:27:48] <mru> there are two pinouts in common use though
  • [00:28:10] <charliex> yeah thats what i thought i used, but this one has 2 and 3 next to each other versus across and down, so just bad luck there.
  • [00:28:43] <charliex> i cancelled my rma number, but strangely they said my serial number wasn't valid, and its the number written on it, i'll post a follow up retracting too
  • [00:29:52] <kholz> k, cool.
  • [00:29:59] <charliex> but at least its working, after the week i've had, i'd just figured it'd be a bad one.
  • [00:30:36] <kholz> I ended up just going with wires and bare (well, heatshrinked) IDC crimp sockets...
  • [00:30:48] <kholz> Serial ports suck.
  • [00:31:11] <kholz> charliex: thats good.
  • [00:31:36] <charliex> i should have done that but i found a idc to db9 in my parts bin, swapped the 2&3 and went from there, looking at the schematic for the chips though its obvious its wrong. i've just created my mmc with my little acer aspire one, lets see if it works.
  • [00:38:30] * rsalveti (n=salveti@189.70.115.68) has joined #beagle
  • [00:38:40] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Remote closed the connection)
  • [00:38:40] <charliex> sucess, i did the split partition mmc and didnt update the bootenv so it paniced on mounting root, but otherwise it worked. sweet
  • [00:39:11] * hli (n=chatzill@vig91-2-82-232-97-149.fbx.proxad.net) Quit ("ChatZilla 0.9.83 [Firefox 3.0.1/2008070208]")
  • [00:39:26] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [00:41:01] <mru> nice, now tradition says you should play the big buck bunny video ;-)
  • [00:42:39] <charliex> i'll try that soon as i succesfully mount a root fs :).
  • [00:55:27] * jkridner_ (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) has joined #beagle
  • [00:55:36] * robclark (n=robclark@166.128.80.158) has joined #beagle
  • [01:02:46] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * harper (n=harper@24-148-50-204.stk-ubr1.chi-stk.il.cable.rcn.com) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * BThompson (n=BThompso@cpe-76-185-93-11.tx.res.rr.com) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * dcordes_ (n=dcordes@unaffiliated/dcordes) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * denix (n=denys@nat/ti/x-950d9d6953d13b6a) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * shoragan (n=shoragan@debian/developer/shoragan) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * ahu (i=ahu@outpost.ds9a.nl) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * bjdooks (n=ben@trinity.fluff.org) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * odesus (n=Omar@201.165.118.65) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:46] * lgentili (i=c82be332@gateway/web/ajax/mibbit.com/x-83bbe7b8dd38e488) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:47] * jkridner (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:47] * keesj (n=keesj@ip49-193-210-87.adsl2.static.versatel.nl) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:47] * ldesnogu (n=ldesnogu@fw-tnat.cambridge.arm.com) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:47] * ds2 (i=noinf@netblock-66-245-251-24.dslextreme.com) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:47] * zarquin (n=zarquin@bright-snat.ucc.asn.au) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:47] * j24 (n=j24@ns32433.ovh.net) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:02:47] * zuh (i=3220610b@emperor.pingu.fi) Quit (kubrick.freenode.net irc.freenode.net)
  • [01:03:17] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [01:03:17] * odesus (n=Omar@201.165.118.65) has joined #beagle
  • [01:03:17] * lgentili (i=c82be332@gateway/web/ajax/mibbit.com/x-83bbe7b8dd38e488) has joined #beagle
  • [01:03:17] * harper (n=harper@24-148-50-204.stk-ubr1.chi-stk.il.cable.rcn.com) has joined #beagle
  • [01:03:17] * BThompson (n=BThompso@cpe-76-185-93-11.tx.res.rr.com) has joined #beagle
  • [01:03:17] * dcordes_ (n=dcordes@unaffiliated/dcordes) has joined #beagle
  • [01:03:17] * jkridner (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) has joined #beagle
  • [01:03:17] * zuh (i=3220610b@emperor.pingu.fi) has joined #beagle
  • [01:03:17] * keesj (n=keesj@ip49-193-210-87.adsl2.static.versatel.nl) has joined #beagle
  • [01:03:17] * ldesnogu (n=ldesnogu@fw-tnat.cambridge.arm.com) has joined #beagle
  • [01:03:17] * ds2 (i=noinf@netblock-66-245-251-24.dslextreme.com) has joined #beagle
  • [01:03:17] * denix (n=denys@nat/ti/x-950d9d6953d13b6a) has joined #beagle
  • [01:03:17] * shoragan (n=shoragan@debian/developer/shoragan) has joined #beagle
  • [01:03:17] * zarquin (n=zarquin@bright-snat.ucc.asn.au) has joined #beagle
  • [01:03:17] * bjdooks (n=ben@trinity.fluff.org) has joined #beagle
  • [01:03:17] * ahu (i=ahu@outpost.ds9a.nl) has joined #beagle
  • [01:03:17] * j24 (n=j24@ns32433.ovh.net) has joined #beagle
  • [01:03:33] * geist (n=geist@c-71-202-119-130.hsd1.ca.comcast.net) has joined #beagle
  • [01:12:41] * jkridner (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) Quit (Read error: 110 (Connection timed out))
  • [01:18:16] <charliex> sweet. booted the ang demo
  • [01:21:22] * robclark (n=robclark@166.128.80.158) Quit (Read error: 110 (Connection timed out))
  • [01:23:10] * lgentili (i=c82be332@gateway/web/ajax/mibbit.com/x-83bbe7b8dd38e488) Quit ("http://www.mibbit.com ajax IRC Client")
  • [01:31:53] * odesus (n=Omar@201.165.118.65) has left #beagle
  • [01:38:17] <dcordes_> charliex: play buckbunny, will ya
  • [01:38:24] * JoeyBorn (n=jborn@dsl017-022-252.chi1.dsl.speakeasy.net) Quit ("gotta keep moving")
  • [01:38:33] <dcordes_> in a loop at least 10 times
  • [01:39:15] <charliex> i'm figuring out how to get bunny to my sd card :)
  • [01:40:14] <charliex> my aspires battery died, so i installed an ext2 drive for windows
  • [01:40:23] <dcordes_> ooohh aspire
  • [01:40:32] <dcordes_> my display hinge hurts when I hear that lol
  • [01:40:57] <dcordes_> you have no sd card with vfat?
  • [01:41:28] <charliex> i formatted it as ext2 dual partition with tiny vfat
  • [01:45:31] <charliex> aight, copy bunny to a 16GB usb stick i got from newegg, charge the aspire and transfer it to ext on the sd...
  • [01:54:28] * banderson (n=irc@69-71-183-7.mammothnetworks.com) has joined #beagle
  • [01:56:23] <charliex> phew, booting the beagle again.
  • [01:56:24] * odesus (n=Omar@201.165.118.65) has joined #beagle
  • [01:56:33] <odesus> good nite!!
  • [01:56:58] <odesus> Does anybody know when is going to be available OMAP3530 in 0.65mm pitch
  • [01:57:06] <charliex> dcordes_: omapfb or mplayer
  • [01:57:22] <dcordes_> mplayer will probably cause an oops
  • [01:57:30] <dcordes_> the alsa is broken
  • [01:57:40] <dcordes_> use omapfbplay, it uses no audio.
  • [01:57:42] <charliex> yeah sound off on that one, ok i started it with omap
  • [01:59:14] <charliex> is there something i should be looking for, or is this an initiation ceremony ;)
  • [02:00:07] <odesus> Does anybody has implemented an applications which works with ARM and DSP at the same time?
  • [02:00:25] <odesus> of OMAP3 processor?
  • [02:01:36] <odesus> anybody?
  • [02:02:28] <odesus> :(
  • [02:04:34] <dcordes_> initiation
  • [02:04:51] <dcordes_> may I ask what sort of display are you using?
  • [02:05:32] <charliex> dvi-d samsung 21"
  • [02:06:49] <charliex> though i plan to use a xenarc 7"
  • [02:06:59] <dcordes_> what interface does that have?
  • [02:07:02] <dcordes_> the xenarc
  • [02:07:22] <charliex> dvi
  • [02:07:33] <dcordes_> what price range is that?
  • [02:08:19] <charliex> 469 usd
  • [02:08:58] <charliex> https://www.xenarcdirect.com/product.php?productid=16194
  • [02:10:20] <dcordes_> costly!
  • [02:10:53] <charliex> yes it is, if i could find a dvi enabled, 7" with usb touchscreen and sunlight/auto capable for cheaper, i'd be a happer camper
  • [02:11:21] <dcordes_> hm yea the dvi is a bitch there
  • [02:11:42] <dcordes_> have you been looking for dvi screens in that size with no touchscreens?
  • [02:12:31] <charliex> not really, though they're a lot more readable in sunlight without the ts
  • [02:12:54] <odesus> charliex: why don't use an adapter dvi-d female to vga-male and use any lcd available?
  • [02:14:47] <charliex> odesus: i could i suppose, its just finding something that matches up the 706 has the high nits for sunlight, they're usually pretty expensive
  • [02:15:11] <charliex> ie a ripoff
  • [02:17:16] <odesus> charliex: thats a problem..
  • [02:17:59] <odesus> charliex: why don't you think in using an common lcd with an epoxic acetate on surface.
  • [02:18:44] <odesus> and a infrarred touchscreen under epoxic over lcd.
  • [02:18:57] <charliex> odesus: thats what most of them are, they have the 3m transflective coating on them.
  • [02:19:29] <charliex> i haven't spent a lot of time looking for one yet, so took the easy route, the beagleboard took me a while to find and i'm hoping i'll be able to use it
  • [02:20:49] <odesus> charliex the problem is sunlight?
  • [02:21:03] <odesus> the visibility?
  • [02:21:54] <charliex> yeah its for in car application so basically outside
  • [02:23:15] <odesus> sorry oled is not available completely yet
  • [02:23:22] <odesus> it will be very useful for you..
  • [02:24:30] <charliex> yes it would, i have some small oleds for buttons, works very well.
  • [02:26:10] <odesus> but there is good options.
  • [02:26:17] <odesus> have you seen windstar lcd screen
  • [02:26:40] <odesus> It supports high temperatures and has a good visibility
  • [02:27:01] <charliex> i will look at it, thanks for the tip
  • [02:27:45] * JoeyBorn (n=jborn@adsl-75-2-249-191.dsl.chcgil.sbcglobal.net) has joined #beagle
  • [02:39:08] * odesus (n=Omar@201.165.118.65) has left #beagle
  • [02:53:11] * dcordes (n=dcordes@unaffiliated/dcordes) has joined #beagle
  • [02:55:21] * montamer (n=vijay@203.199.213.3) has joined #beagle
  • [03:03:49] * JoeyBorn (n=jborn@adsl-75-2-249-191.dsl.chcgil.sbcglobal.net) Quit ("little time with the folks")
  • [03:06:10] * dcordes_ (n=dcordes@unaffiliated/dcordes) Quit (Read error: 110 (Connection timed out))
  • [03:34:01] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [03:34:59] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Client Quit)
  • [03:45:01] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [03:46:09] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Client Quit)
  • [03:50:47] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Read error: 110 (Connection timed out))
  • [03:54:25] * JoeyBorn (n=jborn@adsl-75-3-13-79.dsl.chcgil.sbcglobal.net) has joined #beagle
  • [04:09:06] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [04:16:39] * JoeyBorn (n=jborn@adsl-75-3-13-79.dsl.chcgil.sbcglobal.net) Quit (Read error: 110 (Connection timed out))
  • [04:18:26] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit ()
  • [04:25:43] * Olipro (n=Olipro@uncyclopedia/Olipro) Quit (Read error: 104 (Connection reset by peer))
  • [04:26:00] * Olipro (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [04:28:25] * dcordes (n=dcordes@unaffiliated/dcordes) Quit (Remote closed the connection)
  • [04:36:35] * BThompson (n=BThompso@cpe-76-185-93-11.tx.res.rr.com) Quit ("Trillian (http://www.ceruleanstudios.com")
  • [04:52:49] * dirk2 (n=dirk@F30e4.f.strato-dslnet.de) has joined #beagle
  • [04:55:32] * dirk2 reads the logs
  • [04:57:31] <dirk2> jkridner_: Read your "my current process requires 2 files. uImage and a ramdisk." Not sure if you already have it going, but did you try initramfs?
  • [04:57:36] <dirk2> http://wiki.davincidsp.com/index.php?title=Initrd#initramfs
  • [04:58:46] <dirk2> jkridner_: Some month ago, this was the first way I booted my Beagle. With this, you need a FAT partition and only three files: MLO, u-boot and uImage.
  • [04:59:04] * [g2] (n=tom@nslu2-linux/g2) Quit (Read error: 110 (Connection timed out))
  • [05:00:26] <dirk2> jkridner_: uImage (kernel) contains the ramdisk then. It worked for me with 8MB ramdisk (initramfs). For larger ones you most probably have to re-think load addresses to not overwrite your images at boot.
  • [05:15:39] * JoeyBorn (n=jborn@adsl-75-3-13-79.dsl.chcgil.sbcglobal.net) has joined #beagle
  • [05:20:45] * JoeyBorn (n=jborn@adsl-75-3-13-79.dsl.chcgil.sbcglobal.net) Quit (Read error: 54 (Connection reset by peer))
  • [05:23:35] * Olipro (n=Olipro@uncyclopedia/Olipro) Quit (Read error: 113 (No route to host))
  • [05:26:43] * Olipro (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [05:28:31] * Olipro_ (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [05:30:42] * Olipro__ (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [05:36:26] * dirk2 (n=dirk@F30e4.f.strato-dslnet.de) has left #beagle
  • [05:45:41] * Olipro (n=Olipro@uncyclopedia/Olipro) Quit (Connection timed out)
  • [05:46:09] * Olipro (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [05:47:50] * Olipro_ (n=Olipro@uncyclopedia/Olipro) Quit (Connection timed out)
  • [05:50:40] * Olipro__ (n=Olipro@uncyclopedia/Olipro) Quit (Connection timed out)
  • [06:14:00] * charliex (n=chalrie@mail.finitemonkeys.com) Quit (Read error: 60 (Operation timed out))
  • [06:27:42] * Viral_Sachde (n=Viral_Sa@122.167.159.204) has joined #beagle
  • [07:13:51] * Olipro_ (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [07:15:42] * Olipro__ (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [07:21:41] * Viral_Sachde (n=Viral_Sa@122.167.159.204) Quit (Read error: 104 (Connection reset by peer))
  • [07:21:54] * Viral_Sachde (n=Viral_Sa@122.167.159.204) has joined #beagle
  • [07:28:24] * Olipro (n=Olipro@uncyclopedia/Olipro) Quit (Read error: 110 (Connection timed out))
  • [07:32:59] * Olipro_ (n=Olipro@uncyclopedia/Olipro) Quit (Read error: 110 (Connection timed out))
  • [07:44:27] * rsalveti (n=salveti@189.70.115.68) Quit ("Bye :)")
  • [08:16:48] * valhalla (n=valhalla@81-174-22-56.dynamic.ngi.it) has joined #beagle
  • [08:38:14] * Olipro__ is now known as Olipro
  • [08:50:19] <koen> vlad_: is there a way to use a recent autoconf (say 2.60) with fennec? 2.13 is getting a bit obsolete
  • [08:50:33] * guillaum1 (n=gl@AMontsouris-153-1-28-4.w86-212.abo.wanadoo.fr) Quit ("Leaving.")
  • [08:50:51] * guillaum1 (n=Guillaum@AMontsouris-153-1-28-4.w86-212.abo.wanadoo.fr) has joined #beagle
  • [09:46:13] * Viral_Sachde (n=Viral_Sa@122.167.159.204) has left #beagle
  • [09:46:30] * Beagle2 (n=Beagle2@c170072.adsl.hansenet.de) has joined #beagle
  • [09:46:37] * Beagle2 is now known as torus
  • [09:46:47] * torus is now known as torusle
  • [10:10:46] * torusle (n=Beagle2@c170072.adsl.hansenet.de) Quit ()
  • [10:49:59] * valholl (n=valhalla@81-174-21-205.dynamic.ngi.it) has joined #beagle
  • [10:51:21] * valhalla (n=valhalla@81-174-22-56.dynamic.ngi.it) Quit (Read error: 110 (Connection timed out))
  • [11:06:07] * t_s_o (n=tso@250.84-49-132.nextgentel.com) has joined #beagle
  • [11:21:36] * Crofton (n=balister@70-101-253-100.br1.dav.wv.frontiernet.net) has joined #beagle
  • [11:22:07] * NishanthM (n=Nishanth@cpe-24-27-74-89.tx.res.rr.com) has joined #beagle
  • [11:22:30] * ldesnogu (n=ldesnogu@fw-tnat.cambridge.arm.com) Quit (Read error: 101 (Network is unreachable))
  • [11:23:00] * ldesnogu (n=ldesnogu@fw-tnat.cambridge.arm.com) has joined #beagle
  • [11:23:00] * t_s_o (n=tso@250.84-49-132.nextgentel.com) Quit ("Konversation terminated!")
  • [11:34:52] * dcramer (n=davec@dcdsl.ebox.com) has joined #beagle
  • [11:34:58] <dcramer> morning
  • [11:35:13] <dcramer> I'm using the angstrom demo, there's no support for p2303 ?
  • [11:35:33] <mru> p2303?
  • [11:37:16] <dcramer> usb serial
  • [11:37:39] <mru> why do you want to use that with the beagle?
  • [11:37:48] <dcramer> well, I want more than one serial port
  • [11:38:12] <mru> there's another uart available on the expansion port
  • [11:38:29] <dcramer> yeah, I was aware of that, however the usb serial makes it pretty easy
  • [11:38:37] <mru> true
  • [11:38:41] <mru> no soldering required
  • [11:38:46] * [X]Spot (n=stancho@78.90.115.116) has joined #beagle
  • [11:38:55] <[X]Spot> Hi all
  • [11:39:09] <dcramer> mru: soldering doesn't bother me, just thought I'd plug it in and go
  • [11:39:11] <dcramer> Hi
  • [11:39:42] <[X]Spot> can anybody help me with USB host of the OMAP3 EVM ?
  • [11:39:55] <dcramer> probably
  • [11:40:00] <dcramer> you need the right connector
  • [11:40:46] <[X]Spot> I load the usbocore, ehci-hcd, ohci-hcd modules and connect a usb flash to the usb.. but when I plug the usb flash I do not see anything in dmesg ?
  • [11:41:25] <dcramer> how are you connecting it, you need a cable which has I believe pin 5 grounded
  • [11:41:46] <dcramer> so that linux knows to put it in host mode
  • [11:43:05] <dcramer> I believe there is a way to force it, but I'm not sure of the incantation
  • [11:43:20] <[X]Spot> yes.. but If I connect the omap to the PC usb .. I do no see anyting on the PC (like new hardware found and so on)
  • [11:43:38] <[X]Spot> The modules are loaded correct
  • [11:43:39] <[X]Spot> but ..
  • [11:43:41] <dcramer> that you should
  • [11:43:52] <dcramer> it should show a ethernet gadget device
  • [11:44:38] <[X]Spot> yes.. but nothing
  • [11:45:28] <dcramer> strange
  • [11:45:34] * Crofton (n=balister@70-101-253-100.br1.dav.wv.frontiernet.net) Quit ("Leaving")
  • [11:45:38] <dcramer> is it connected while loading ?
  • [11:46:19] <[X]Spot> yes
  • [11:46:59] <dcramer> not sure what to say, bad cable ?
  • [11:47:05] <dcramer> bad hardware somewhere ?
  • [11:47:09] <dcramer> certainly works here
  • [11:47:10] <[X]Spot> when exactly should I see that a new hardware is detected (on the PC)... when the power is on? when the kernel is loaded? when the usb modules re loaded ?
  • [11:47:24] <dcramer> what is the the pc running ?
  • [11:47:27] <dcramer> linux ?
  • [11:47:31] <[X]Spot> windows
  • [11:47:38] <[X]Spot> I tried with different cables.. but do not have another EVM to try
  • [11:47:41] <dcramer> then you should see it when you plug it in
  • [11:47:49] <[X]Spot> any jumbers ? any kernel dependencies ?
  • [11:47:55] <dcramer> oh, how are you powering the evm
  • [11:48:01] <dcramer> I use the pc to power it
  • [11:48:07] <dcramer> not the 5v supply
  • [11:48:14] <dcramer> in other words the usb
  • [11:48:14] <[X]Spot> what do you mean ?
  • [11:48:20] <[X]Spot> hm
  • [11:48:28] <[X]Spot> s If I plug the USB
  • [11:48:31] <[X]Spot> to the PC and EVM
  • [11:48:41] <[X]Spot> the EVM should run ?
  • [11:48:42] <dcramer> yes
  • [11:48:58] <[X]Spot> any jumbers? any buttons ?
  • [11:49:01] <dcramer> nope
  • [11:49:04] <[X]Spot> something that should be set
  • [11:49:05] <dcramer> just works
  • [11:49:05] <[X]Spot> hmm
  • [11:49:08] <[X]Spot> very strange
  • [11:49:13] <[X]Spot> it seems that the EVM is broken
  • [11:49:16] <dcramer> sounds like
  • [11:49:29] <dcramer> which really sucks because they are apparenlty very hard to get
  • [11:49:50] <dcramer> I presume your pc USB works with other things ?
  • [11:51:19] <[X]Spot> yes
  • [11:51:25] <dcramer> sorry, gotta run
  • [11:51:26] <[X]Spot> I have beagleboard as well
  • [11:51:33] <[X]Spot> and it runs when I plug the cable
  • [11:51:36] <[X]Spot> the USB
  • [11:51:39] <[X]Spot> but the EVM - nope
  • [11:51:45] <dcramer> oh, I thought we were talking the beagleboard
  • [11:51:47] <dcramer> my mistake
  • [11:54:52] <[X]Spot> but the EVM should power as well (from the USB) ?
  • [11:58:16] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [12:00:18] * likewise (n=chatzill@82-171-51-231.ip.telfort.nl) has joined #beagle
  • [12:00:23] <likewise> hey folks
  • [12:02:00] <likewise> jrmuizel: thanks for the cairo/pixman ARM asm patch
  • [12:08:07] <likewise> koen: which ffmpeg does beagleboard use? the git one in OE?
  • [12:08:43] * likewise is now known as like|bbiab
  • [12:11:19] <jrmuizel> like|bbiab: your welcome, there will be more coming
  • [12:12:10] * like|bbiab is now known as likewise
  • [12:12:39] <likewise> jrmuizel: in the armv5 department?
  • [12:13:26] <jrmuizel> likewise: the stuff that I wrote is actually armv6
  • [12:13:32] <jrmuizel> or some of it is anyways
  • [12:13:50] <[X]Spot> dcramer do you know should the EVM power from the USB ?
  • [12:14:00] <[X]Spot> not the beagleboard
  • [12:14:03] <likewise> jrmuizel: i was afraid of that, i have a armv5 here :-)
  • [12:14:04] <jrmuizel> I mostly care about armv6
  • [12:14:34] <jrmuizel> likewise: some of it should still work on armv5
  • [12:15:17] <jrmuizel> I think the instruction I use from armv6 is 'usat' in one function
  • [12:15:31] <jrmuizel> s/the instruction/the only instruction/
  • [12:16:41] <jrmuizel> so it should be pretty easy to do an ifdef armv5 version
  • [12:16:53] <likewise> jrmuizel: ok, my arm asm mnemonic knowledge is stale, but I certainly will have a look at armv5 based on your work then. (IXP42x)
  • [12:17:55] <jrmuizel> hmmm..
  • [12:18:20] <jrmuizel> i also use uqadd8
  • [12:18:37] <jrmuizel> which makes a big difference
  • [12:18:48] <likewise> I guess most of the interesting SIMD is in armv6 :-)
  • [12:18:54] <jrmuizel> yep
  • [12:20:11] <likewise> Maybe the new tesselation or scanline approaches give a better boost then.
  • [12:20:47] <jrmuizel> however, I'd guess there's still a fair bit of room for improvement even on armv5
  • [12:21:36] <jrmuizel> the scanline rasterizer should help, and there's room for improvement there too
  • [12:22:30] <likewise> interesting. have to break off and fetch my bike from the shop now before it closes. bbiab, cya later.
  • [12:22:39] * likewise is now known as like|bbiab
  • [12:24:58] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Remote closed the connection)
  • [12:25:43] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [12:36:23] * harper_ (n=harper@24-148-50-204.stk-ubr1.chi-stk.il.cable.rcn.com) has joined #beagle
  • [12:40:20] * harper (n=harper@24-148-50-204.stk-ubr1.chi-stk.il.cable.rcn.com) Quit (Read error: 110 (Connection timed out))
  • [12:51:43] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit ()
  • [13:06:28] * dcordes (n=dcordes@unaffiliated/dcordes) has joined #beagle
  • [13:14:21] <[X]Spot> i am trying to run madplay on OMAP3 EVM.. I tried to compile to source and received an error : "Floating point exception" when tried to start it.. I download it from the angstrom repository - the same..
  • [13:14:26] <[X]Spot> do you have any idea ?
  • [13:15:38] <dcordes> are there any news regarding alsa?
  • [13:17:22] * felipec (n=felipec@a88-113-6-167.elisa-laajakaista.fi) has joined #beagle
  • [13:28:47] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [13:33:43] <dcramer> [X]Spot: sorry I have no idea
  • [13:39:39] <like|bbiab> [X]Spot: probably your toolchain does not use the same ABI model as the one that built the kernel and/or C library on your machine.
  • [13:40:00] <like|bbiab> [X]Spot: Or did you use the Angstrom kernel and userspace as well?
  • [13:40:24] <dcramer> any links to building the Angstrom kernel
  • [13:43:08] * like|bbiab is now known as likewise
  • [13:49:02] * torus (n=torus@c170072.adsl.hansenet.de) has joined #beagle
  • [13:49:05] <torus> hi.
  • [13:49:38] <mru> hi
  • [13:50:46] <dcordes> hi
  • [13:51:05] <torus> hm. seems like I really need linux on my desktop for proper development..
  • [13:51:26] <dcordes> mru: do you have a kernel build somehwere that is hdmi tv rady and has usb host?
  • [13:51:30] <dcordes> or otg
  • [13:51:38] <torus> what distributions do you guys use?
  • [13:51:54] <dcordes> mru: I'd like to make a quick demo and have my build tree hosed
  • [13:52:33] <dcordes> torus: I can suggest using linux to do kernel building and so. I use ubuntu
  • [13:52:40] <mru> dcordes: sorry, I don't have usb host enabled
  • [13:53:06] <torus> dcordes. thanks.. I'll give it a try.
  • [13:54:06] <dcordes> mru: what cmdline must I put to have the hdmi tv work with your latest tree?
  • [13:54:39] <torus> dcordes, nice.. not a 15 gb download (like debian) :-)
  • [13:54:52] <dcordes> video=omapfb:mode=720p60,vram=2M,vram=4M
  • [13:55:06] <mru> that should work
  • [13:55:08] <dcordes> torus: 15gb what?
  • [13:55:10] <dcordes> ok
  • [13:55:22] <dcordes> 5 files changed, 225 insertions(+), 81 deletions(-)
  • [13:55:58] * dcramer (n=davec@dcdsl.ebox.com) Quit (Read error: 104 (Connection reset by peer))
  • [13:56:22] <torus> dcordes. jep. network install does not work on my machine.. so you need the whole thing...
  • [13:56:54] <dcordes> default video mode will override the cmdline "mode=" ?
  • [13:57:04] <mru> no
  • [13:57:08] <mru> the other way around
  • [13:57:20] <mru> if you specify something in the config, you don't need the cmdline
  • [13:57:33] <mru> but cmdline will override if present
  • [13:59:58] <dcordes> there's only the default mode switch
  • [14:01:20] <mru> the order is cmdline, CONFIG_FB_OMAP_VIDEO_MODE, hardcoded board default
  • [14:03:57] <dcordes> ok
  • [14:04:13] <dcordes> I hope that boots now
  • [14:04:35] <dcordes> my .config is funny
  • [14:05:38] * dcramer (n=davec@dcdsl.ebox.com) has joined #beagle
  • [14:10:41] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [14:14:24] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Read error: 110 (Connection timed out))
  • [14:21:17] * ldesnogu (n=ldesnogu@fw-tnat.cambridge.arm.com) Quit (Read error: 110 (Connection timed out))
  • [14:30:31] * jkridner (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) has joined #beagle
  • [14:32:58] <jkridner> good morning all
  • [14:33:26] * feig (n=ejf3@cpe-66-66-112-67.rochester.res.rr.com) has joined #beagle
  • [14:38:01] * jkridner_ (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) Quit (Read error: 110 (Connection timed out))
  • [14:39:31] * t_s_o (n=tso@250.84-49-132.nextgentel.com) has joined #beagle
  • [14:40:15] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-3916fe74d5684fce) has joined #beagle
  • [14:44:03] * Beagle1 (n=Beagle1@219.86.166.165) has joined #beagle
  • [14:45:20] * harper_ (n=harper@24-148-50-204.stk-ubr1.chi-stk.il.cable.rcn.com) Quit (Read error: 110 (Connection timed out))
  • [14:47:40] * Beagle1 (n=Beagle1@219.86.166.165) Quit (Client Quit)
  • [14:48:35] * ldesnogu (n=ldesnogu@fw-tnat.cambridge.arm.com) has joined #beagle
  • [14:54:47] * torus (n=torus@c170072.adsl.hansenet.de) Quit ("(installing linux...)")
  • [14:54:56] * NishanthM (n=Nishanth@cpe-24-27-74-89.tx.res.rr.com) Quit (Read error: 110 (Connection timed out))
  • [14:55:06] * valholl (n=valhalla@81-174-21-205.dynamic.ngi.it) Quit ("Leaving")
  • [15:02:05] * BThompson (n=BThompso@cpe-76-185-93-11.tx.res.rr.com) has joined #beagle
  • [15:03:44] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-3916fe74d5684fce) Quit ("http://www.mibbit.com ajax IRC Client")
  • [15:12:10] * NishanthM (n=Nishanth@cpe-24-27-74-89.tx.res.rr.com) has joined #beagle
  • [15:13:54] * t_s_o (n=tso@250.84-49-132.nextgentel.com) Quit ("Konversation terminated!")
  • [15:17:06] * [g2] (n=tom@nslu2-linux/g2) has joined #beagle
  • [15:27:33] * jkridner_ (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) has joined #beagle
  • [15:28:30] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-1ac7d8e57a8469f2) has joined #beagle
  • [15:31:08] * feig (n=ejf3@cpe-66-66-112-67.rochester.res.rr.com) Quit ("Konversation terminated!")
  • [15:35:57] * jkridner (n=jason@c-76-31-18-64.hsd1.tx.comcast.net) Quit (Read error: 110 (Connection timed out))
  • [15:36:07] * jkridner_ is now known as jkridner
  • [15:38:19] * pmeerw_ (n=pmeerw@85-127-149-38.dynamic.xdsl-line.inode.at) has joined #beagle
  • [15:38:45] * likewise (n=chatzill@82-171-51-231.ip.telfort.nl) Quit ("ChatZilla 0.9.83 [Firefox 3.0/2008061015]")
  • [15:39:36] <pmeerw_> hi
  • [15:41:18] <pmeerw_> comment on errata #8: my board/cable showed all symptoms of errata #8 (ie. serial output, but can't type anything)
  • [15:41:51] <pmeerw_> but I ONLY had the issue when DC powered; when USB powered serial input was fine
  • [15:42:13] <pmeerw_> turned out pin 5 (ground) was miswired
  • [15:42:18] <pmeerw_> happy now :)
  • [15:44:50] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit ()
  • [15:46:56] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [15:48:50] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-1ac7d8e57a8469f2) Quit ("http://www.mibbit.com ajax IRC Client")
  • [15:51:21] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Client Quit)
  • [15:57:37] <dcordes> is the timeout until bootcmd hardcoded in uboot?
  • [15:57:52] <dcordes> it's 10 seconds in my flash very annoying
  • [16:02:59] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [16:03:52] <dcordes> mru: did you integrate freq scaling?
  • [16:04:44] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-a0ffddb05c20d725) has joined #beagle
  • [16:07:34] <lgentili> jkridner: ping
  • [16:07:42] <jkridner> pong
  • [16:07:54] <lgentili> can I suggest something?
  • [16:07:58] <lgentili> what about to include in the beagleboard the wiring for the serial port?
  • [16:08:04] <lgentili> I read alot of ppl p
  • [16:08:12] <lgentili> having problem with that
  • [16:08:48] <lgentili> has not a real cost, and it's wasting alot ppl time
  • [16:09:17] <jkridner> k. we can extract it from the Hardware Reference Manual and http://www.pccables.com/07120.htm to put it on beagleboard.org/support/faq.
  • [16:09:31] <lgentili> cool
  • [16:09:57] <jkridner> it would be nice if someone could draw the picture at http://www.pccables.com/07120.htm, since I don't have rights to it.
  • [16:11:36] <jkridner> btw, it is already on http://elinux.org/BeagleBoardFAQ#Serial_connection_.231
  • [16:11:43] <jkridner> just no picture.
  • [16:12:27] <lgentili> what about include the IDC cable in the kit?
  • [16:13:20] * t_s_o (n=tso@250.84-49-132.nextgentel.com) has joined #beagle
  • [16:14:07] <jkridner> working on it. Digi-Key currently doesn't stock it.
  • [16:14:20] <lgentili> ok
  • [16:14:23] <jkridner> they weren't happy with the first prototypes that they had, so they've had to go back to the manufacturer.
  • [16:14:35] <jkridner> it'll be a "highly recommended add-on"...
  • [16:14:44] <jkridner> shouldn't be but a few dollars.
  • [16:15:02] <lgentili> yep
  • [16:15:34] <jkridner> I know the pain is to include a separate shipping fee to go to the one listed on http://beagleboard.org/hardware.
  • [16:17:35] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit ()
  • [16:18:02] <lgentili> It should be posted in digikey's site under "featured peripherials"
  • [16:18:16] <lgentili> with the null modem, DVI adapter, etc
  • [16:19:06] <lgentili> you made that webpage or digkey?
  • [16:19:58] * TAK2004 (n=thomas@dslb-088-072-206-250.pools.arcor-ip.net) has joined #beagle
  • [16:20:33] <jkridner> does this work: http://beagleboard.org/support/faq/
  • [16:20:44] <jkridner> digikey.
  • [16:21:06] <jkridner> we talk about the need to have the adapter provided in the "featured peripherals" section every week.
  • [16:21:09] <TAK2004> where i can find the sourcecode of the prebuild busybox from http://code.google.com/p/beagleboard/wiki/BeagleSourceCode
  • [16:21:12] <jkridner> we spoke about it just yesterday.
  • [16:21:24] <lgentili> ok
  • [16:21:51] <lgentili> maybe add the standard serial settings "115200 8n1... etc" ?
  • [16:22:13] <jkridner> TAK2004: no one has asked for it before (and there were no thoughts of it being interesting, since there are other good places to get a better file system starting point).
  • [16:22:20] <jkridner> TAK2004: I'll ask Khasim to post them!
  • [16:22:27] <TAK2004> thx
  • [16:22:34] <jkridner> I don't think busybox is patched in any way.
  • [16:22:48] <jkridner> I think it is a stock 1.9 tarball, but Khasim should confirm.
  • [16:23:35] * Xenion (n=robert@dslb-088-072-206-250.pools.arcor-ip.net) has joined #beagle
  • [16:23:35] <lgentili> ok it's explained in the Serial connection #2
  • [16:23:37] <jkridner> compilation was either csl 2007q1 or 2007q3. (not sure why Khasim still occasionally uses 2007q1, since I think 2007q3 is better in all respects)
  • [16:23:41] <Xenion> hello jkridner
  • [16:23:43] <Xenion> :-)
  • [16:23:45] <lgentili> http://elinux.org/BeagleBoardFAQ#Serial_connection_.231
  • [16:24:10] <Xenion> jkridner, sorry to intrude the conversation on busybox ..
  • [16:24:12] <jkridner> I'm trying to keep the "official" FAQ very short.
  • [16:24:20] <lgentili> ok, good point
  • [16:24:32] <Xenion> what gnu toolchain is recommended for BB when busybox isn't ?
  • [16:24:35] <jkridner> I think we are done with busybox... just need to get Khasim to post the sources.
  • [16:25:12] <jkridner> http://elinux.org/BeagleBoard#Compiler
  • [16:25:31] <jkridner> csl 2007q3 is the most stable compiler to use.
  • [16:25:44] <Xenion> i see
  • [16:25:53] <Xenion> sorry i just overlooked it
  • [16:26:24] <jkridner> http://www.codesourcery.com/gnu_toolchains/arm/portal/release313
  • [16:26:43] <jkridner> no worries. It is nice to be able to cut-and-paste answers. :)
  • [16:26:43] <Xenion> sorry jkridner i meant the gnu binary tools
  • [16:26:53] <jkridner> binutils?
  • [16:26:55] <Xenion> jkridner, links are great :-)
  • [16:27:01] <Xenion> jkridner, absoluty yes the binutils
  • [16:27:11] <jkridner> part of the GCC download.
  • [16:27:23] <Xenion> i see
  • [16:27:35] <Xenion> i'll look into this .. the download is quite slow :-)
  • [16:27:40] <chakie> it's going to be interesting for a total n00b like me to actually filter through all the projects, pages and patches to get to the real meat
  • [16:28:02] <lgentili> this http://code.google.com/p/beagleboard/wiki/outofthebox is really well done, and useful
  • [16:28:24] <chakie> looks good
  • [16:28:35] <chakie> i've barely had time to unpack it yet (and snap some pics)
  • [16:29:57] <jkridner> lgentili: khasim did the work. I just couldn't stand looking at that OOMAP anymore, so I removed the first "O".
  • [16:31:28] <lgentili> hehe, I was to say that typo
  • [16:36:12] <lgentili> you are correcting typos :P
  • [16:37:18] <lgentili> I saw a "begle" and now is corrected
  • [16:41:27] * felipec (n=felipec@a88-113-6-167.elisa-laajakaista.fi) Quit ("Leaving")
  • [16:42:28] <pmeerw_> jkridner: I sorted my problems with serial; errata #8 sounds so similar, but in the end pin #5 (ground) was not properly connected
  • [16:44:32] <lgentili> would be nice to do a video with the kashim steps http://code.google.com/p/beagleboard/wiki/outofthebox
  • [16:44:34] <lgentili> ;)
  • [16:45:06] <lgentili> you have your actor part jkridner
  • [16:45:52] <lgentili> I saw the you tube video you have made and was pretty good
  • [16:46:14] <lgentili> the one you explain the bb holding a board
  • [16:47:08] <lgentili> I don't know how many times you tried, but that was fluid :)
  • [16:48:25] <_apk> where can I find all the different modes that can be specified on boot cmd line? (e.g. video=omapfb:mode=720p60)
  • [16:56:40] <lgentili> I don't find that info in the wiki
  • [16:57:18] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [16:57:35] <mru> _apk: in the source
  • [16:58:30] <_apk> mru, yep...I thought that they were written somewhere in the wiki :)
  • [16:59:12] <lgentili> from linux omap archive say for example, video=omapfb:rotate:<degree> to see the penguin rotate, but that only 1 parm
  • [16:59:30] <lgentili> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg00825.html
  • [16:59:54] <lgentili> mru: this should be the file? drivers/video/omap/omapfb_main.c |
  • [17:01:32] <mru> yes
  • [17:06:40] <TAK2004> drivers/i2c/chips/twl4030_power.c:23:38: error: asm/arch/power_companion.h: No such file or directory
  • [17:06:43] * sruffell (n=sruffell@adsl-074-185-078-025.sip.bhm.bellsouth.net) has joined #beagle
  • [17:06:48] * torus (n=torus@c170072.adsl.hansenet.de) has joined #beagle
  • [17:06:51] <torus> re.
  • [17:06:54] <TAK2004> can someone help me with this ?
  • [17:08:35] <ahu> TAK2004: that is a pretty rare error
  • [17:08:40] <ahu> where did you get your kernel sources?
  • [17:08:55] <TAK2004> official bb site
  • [17:10:03] <ahu> weird - perhaps twl4030 bitrotted
  • [17:10:49] <Xenion> how can TAK2004 get rid of this twl4030 ?
  • [17:11:10] <Xenion> im sitting beside him and are wondering why the kernel makefile selects it for compile
  • [17:11:43] <ahu> try editing the .config file and removing it manually
  • [17:11:48] <ahu> it might be turned on automatically though
  • [17:12:04] <ahu> in that case, drivers/i2c/chips/Kconfig might explain why
  • [17:12:11] <ahu> it might be enabled because of something else
  • [17:14:16] * Olipro_ (n=Olipro@uncyclopedia/Olipro) has joined #beagle
  • [17:16:25] <Xenion> ahu it wont disable
  • [17:16:27] <Xenion> hm
  • [17:16:34] <Xenion> is there some way to get the source ?
  • [17:18:31] <ahu> Xenion: there are probably some rules that require it then
  • [17:18:44] <Xenion> ahu i looked through the config but got no clue
  • [17:18:55] <Xenion> it states that it depends on HAS_IOMEM
  • [17:19:00] <Xenion> which is quite sensless
  • [17:19:42] <ahu> the other way around might be the issue
  • [17:19:52] <ahu> you could simply try commenting out the #include line
  • [17:20:32] <Xenion> yeah that sound professional :d
  • [17:23:28] * rsalveti (n=salveti@189.70.115.68) has joined #beagle
  • [17:23:56] <Xenion> thanks ahu seeya later
  • [17:24:06] <Xenion> maybe you can help TAK2004 a bit further
  • [17:27:16] * Xenion (n=robert@dslb-088-072-206-250.pools.arcor-ip.net) Quit ("Verlassend")
  • [17:30:41] * Olipro (n=Olipro@uncyclopedia/Olipro) Quit (Read error: 110 (Connection timed out))
  • [17:34:56] * rsalveti (n=salveti@189.70.115.68) Quit ("Bye :)")
  • [17:42:20] <TAK2004> default kernel config of http://code.google.com/p/beagleboard/wiki/BeagleSourceCode is broken :\
  • [17:43:51] * torus (n=torus@c170072.adsl.hansenet.de) Quit ()
  • [17:44:56] <TAK2004> drivers/i2c/chips/twl4030_power.c:23:38: error: asm/arch/power_companion.h: No such file or directory
  • [17:45:04] <TAK2004> [thomas@localhost ~]$ locate power_companion.h
  • [17:45:04] <TAK2004> /home/thomas/Desktop/2.6_kernel/include/asm-arm/arch-omap/power_companion.
  • [17:45:21] <TAK2004> wrong path or wrong dir name
  • [17:45:22] * rsalveti (n=salveti@189.70.115.68) has joined #beagle
  • [18:00:15] * rsalveti (n=salveti@189.70.115.68) Quit (Read error: 104 (Connection reset by peer))
  • [18:08:24] * rsalveti (n=salveti@189.70.115.68) has joined #beagle
  • [18:11:16] * JoeyBorn (n=jborn@adsl-75-2-246-249.dsl.chcgil.sbcglobal.net) has joined #beagle
  • [18:43:10] * JoeyBorn (n=jborn@adsl-75-2-246-249.dsl.chcgil.sbcglobal.net) Quit ("lots of monkey business")
  • [18:47:53] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) has joined #beagle
  • [19:04:40] * jrmuizel (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit (Read error: 110 (Connection timed out))
  • [19:08:36] * dcramer (n=davec@dcdsl.ebox.com) Quit (Read error: 104 (Connection reset by peer))
  • [19:09:12] * dcramer (n=davec@dcdsl.ebox.com) has joined #beagle
  • [19:10:16] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-a0ffddb05c20d725) Quit ("http://www.mibbit.com ajax IRC Client")
  • [19:11:11] * hli (n=chatzill@vig91-2-82-232-97-149.fbx.proxad.net) has joined #beagle
  • [19:14:24] * hli (n=chatzill@vig91-2-82-232-97-149.fbx.proxad.net) Quit (Client Quit)
  • [19:14:41] * hli (n=chatzill@vig91-2-82-232-97-149.fbx.proxad.net) has joined #beagle
  • [19:15:47] * felipec (n=felipec@a88-113-6-167.elisa-laajakaista.fi) has joined #beagle
  • [19:17:54] * hli (n=chatzill@vig91-2-82-232-97-149.fbx.proxad.net) Quit (Client Quit)
  • [19:21:20] * hli (n=chatzill@vig91-2-82-232-97-149.fbx.proxad.net) has joined #beagle
  • [19:27:47] * rsalveti (n=salveti@189.70.115.68) Quit ("Bye :)")
  • [19:31:18] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-04ef995e70b2265f) has joined #beagle
  • [19:34:19] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-04ef995e70b2265f) Quit (Client Quit)
  • [19:34:31] * Xenion (n=robert@p579FC2E9.dip.t-dialin.net) has joined #beagle
  • [19:34:37] <Xenion> hello again :-)
  • [19:36:45] <TAK2004> now i got the Image and zImage but no uImage because i have no mkimage
  • [19:37:25] * jrmuizel_ (n=jrmuizel@CPE001f5be79d0f-CM0017ee62f8b0.cpe.net.cable.rogers.com) Quit ()
  • [19:40:19] <Xenion> Guten Abend alle miteinander / Hello folks :-)
  • [19:40:41] <Xenion> great TAK2004
  • [19:42:08] * NishanthMenon (n=Nishanth@cpe-24-27-74-89.tx.res.rr.com) has joined #beagle
  • [19:44:25] * NishanthM (n=Nishanth@cpe-24-27-74-89.tx.res.rr.com) Quit (Read error: 110 (Connection timed out))
  • [19:44:40] * rsalveti (n=salveti@189.70.115.68) has joined #beagle
  • [19:50:18] * sruffell (n=sruffell@adsl-074-185-078-025.sip.bhm.bellsouth.net) Quit ("Leaving.")
  • [20:12:07] * torus (n=torus@c170072.adsl.hansenet.de) has joined #beagle
  • [20:13:13] <torus> It's official: I'm to dump to get wlan working under linux on my notebook... Guess I have to stick with cygwin and find a way to get my rootfs onto the ext2 partition of my sdcard some other way..
  • [20:16:53] <Xenion> torus, did you ask for help in #linuxeinsteiger on irc.euirc.net ?
  • [20:17:15] <keesj> torus: :)
  • [20:17:50] <torus> Xenion. nope. not yet. The problem is: it's rather hard to ask something if you don't have internet... I always have to reboot to xp.
  • [20:17:52] <keesj> TAK2004: mkimage is part of uboot
  • [20:18:29] <Xenion> hehe
  • [20:18:30] <Xenion> i see
  • [20:18:33] <TAK2004> at the moment i try to compile it
  • [20:18:34] <torus> catch22
  • [20:18:46] <TAK2004> but no configure :\
  • [20:18:52] <Xenion> torus, i'm just curios what kind of hardware and distro you've tried
  • [20:20:10] <torus> Xenion: ubuntu
  • [20:20:52] <Xenion> torus, and on what hardware ?
  • [20:20:53] <TAK2004> *run around and cry*
  • [20:21:30] <torus> Xenion, asus notebook. ought to work fine.
  • [20:21:38] <Xenion> hm
  • [20:22:04] <Xenion> old one or new one ? ( the old got a ipw2200 the new ones a intel 82xxx bgn
  • [20:23:02] <torus> Xenion, new one.. driver gets detected and everything works fine. I think the driver just does never really power up the radio.. (because if I boot to xp after having run linux I have to jump through multiple loops to get my wlan activated again)...
  • [20:23:15] <torus> asus X50R btw.
  • [20:23:33] <Xenion> hehe torus thats an easy one ;)
  • [20:23:40] <Xenion> trust me
  • [20:23:48] <Xenion> you've got a so called kill switch
  • [20:24:05] <keesj> NishanthMenon: I looked a the linkt they apparently also really setup the scan chain and don't pull down the pins
  • [20:24:14] <Xenion> that is the explanation why you have to reboot in rounds to get it working again
  • [20:24:24] <torus> Xenion, I already use the killswitch..
  • [20:24:33] <Xenion> torus, just look in google howto disable your killswitch .. or disable it in the bios
  • [20:24:33] <torus> works most of the time.
  • [20:25:24] <torus> will do.
  • [20:25:29] <torus> thanks
  • [20:26:33] <Xenion> hm torus do you use wpa_supplicant on linux ?
  • [20:26:53] <Xenion> or do you rely on the ubuntu network_manager
  • [20:27:07] <torus> don't know - should I? really - I just installed ubuntu and not much more...
  • [20:27:48] <torus> oh - and I had to install the build-essentials.. (how stupid is that - a linux workstation w/o headers is useless)
  • [20:28:28] <Xenion> http://www.k-40.de/debian-notebook.htm <- maybe this helps
  • [20:28:54] <Xenion> torus, just some tip .. don't use ubuntu if you're want to use linux for development
  • [20:29:11] <Xenion> ubuntu is just usable for browsing the web .. if at all ..
  • [20:29:25] <Xenion> for development i can really recommend you fedora
  • [20:29:45] <Xenion> fedora has the ATRPMS Repository ther's always the latest atheros Madwifi version driver avaible
  • [20:29:49] <Xenion> and
  • [20:30:05] <Xenion> Fedora does install all development tools and libs for you even at setup stage ..
  • [20:30:06] <Xenion> :-)
  • [20:30:34] <Xenion> so much for that .. now i'll remain silent .. it's a beagleboard channel ^^
  • [20:30:51] <Xenion> TAK2004, sorry didn't you just had trouble compiling uboot ?
  • [20:31:01] <torus> Xenion. thanks for the recommendation. I'll try fedora then..
  • [20:31:17] <torus> lets just hope it's not a 15gig download like debian :-)
  • [20:31:25] <Xenion> 3.4 ;)
  • [20:31:41] <Xenion> <- RHCE ( RedHat Certified Engineer ... ) :-)
  • [20:34:31] <Xenion> just a question to the more advanced beagle's ... is it possible to switch the power domains in-time ? ( like using cpuspeed on a linux laptop ? )
  • [20:34:36] <TAK2004> it works :)
  • [20:35:47] <TAK2004> it booted extremly fast :)
  • [20:36:46] <Xenion> great TAK2004 !
  • [20:36:56] <Xenion> now you've got a kernel with ... nothing ! ^^
  • [20:37:16] <TAK2004> i love u2
  • [20:38:33] <Xenion> TAK2004, you've now got 2 choices left .. you gonna watch stargate .. or you get SSHD to work ^^
  • [20:47:31] * torus (n=torus@c170072.adsl.hansenet.de) Quit ()
  • [21:01:19] * lgentili (i=bee0ec82@gateway/web/ajax/mibbit.com/x-ca7c31c36aed5933) has joined #beagle
  • [21:23:53] * amitu (n=amitu@cpe-67-49-44-99.socal.res.rr.com) has joined #beagle
  • [21:25:23] * amitu (n=amitu@cpe-67-49-44-99.socal.res.rr.com) Quit (Remote closed the connection)
  • [21:29:12] * TAK2004 (n=thomas@dslb-088-072-206-250.pools.arcor-ip.net) Quit (Remote closed the connection)
  • [21:30:21] <pmeerw_> is there a way to enable USB host mode without an OTG cable?
  • [21:31:17] <geist> i'm pretty sure you can jam the msusb into host mode directly
  • [21:31:48] <geist> hypothetically, not sure if linux driver has an option for that
  • [21:32:02] * Xultz (n=axc@201.47.13.36.adsl.gvt.net.br) has joined #beagle
  • [21:32:15] <pmeerw_> hm, the Nokia N810 can do it, let's see if it works the same way...
  • [21:32:28] <geist> same part, yeah
  • [21:32:57] <Xultz> Hello friends, I am a bit confuse about connecting a LCD monitor to a beagle board, can someone please help me?
  • [21:36:01] <Xultz> please?
  • [21:36:14] <geist> i dunno, I haven't tried connecting mine yet
  • [21:36:24] <geist> need to grab a hdmi->dvi cable today
  • [21:36:52] <Xultz> my confusion it, the specs of the beagle says the connector is a DVI-D
  • [21:37:14] <geist> yeah, that's why it can't drive my hdmi TV
  • [21:37:22] <Xultz> my monitor is a Dell 1908FP, wich says: 1 x DVI-D - 24 pin digital DVI as a connection
  • [21:37:31] <geist> friend of mine just got a converter cable and worked fine on his dell 2407
  • [21:37:41] <Xultz> do I need to buy a DVI -> HDMI cable?
  • [21:37:46] <geist> i think it's because hdmi usually contains essentially dvi-d signalling
  • [21:37:53] <geist> so the cable is really just breaking it out
  • [21:37:59] <geist> and yeah, you need a converter cable
  • [21:38:37] <Xultz> it means that the HDMI out of the cable is compatible with the DVI input of my monitor?
  • [21:38:58] <geist> provided you get a converter cable, yes
  • [21:39:23] <geist> note: i haven't actually tried this yet, gonna go by Fry's in a bit and grab a cable
  • [21:39:32] <Xultz> the "HDMI to DVI-D cable available from Digi-Key" does that job, so?
  • [21:39:39] <geist> probably, yes
  • [21:40:17] <Xultz> with that same cable is it possible to connect to a LCD television?
  • [21:40:24] <geist> that i do not know
  • [21:43:18] * torus (n=nils@c170072.adsl.hansenet.de) has joined #beagle
  • [21:43:33] <torus> re - whoever helped me with my linux-problems.. they're solved...
  • [21:43:42] <torus> thanks a lot!
  • [21:45:28] <Xenion> torus, glad to hear that :-)
  • [21:47:14] <torus> wlan driver firmware was missing..
  • [21:47:34] <torus> okay - no I can start to actually develop on the beagleboard.
  • [21:47:34] <Xenion> :-)
  • [21:48:32] <Xenion> torus, thats crepy ... i hope on day all manufactures will publish there specs like intel did .. so wlan will work out-of-the-box for everyone :-)
  • [21:48:51] <pmeerw_> regarding usb host mode: /sys/devices/platform/musb_hdrc.0/mode
  • [21:49:02] <Xenion> Gute Nacht alle miteinander / Good Night folks ! :-)
  • [21:49:13] <torus> Xenion, well - an error-message would have been nice.. (nacht!)
  • [21:49:29] <pmeerw_> it doesn't work; mode sits at b_idle
  • [21:49:30] <Xenion> torus, i bed "dmesg" contained an error ;)
  • [21:49:41] <torus> Xenion, jep.
  • [21:49:59] <pmeerw_> echo "peripheral" > mode gives a oops
  • [21:51:52] * Xenion (n=robert@p579FC2E9.dip.t-dialin.net) Quit ("Verlassend")
  • [21:55:39] * Xultz (n=axc@201.47.13.36.adsl.gvt.net.br) Quit (Remote closed the connection)
  • [21:56:14] <geist> yeah, that musb driver is pretty hateful
  • [21:56:30] <geist> actually the musb hardware is pretty lame, i have to deal with it in an alternate reality
  • [21:56:37] <geist> it's pretty full of errata
  • [21:56:48] * t_s_o (n=tso@250.84-49-132.nextgentel.com) Quit ("Konversation terminated!")
  • [21:57:02] <geist> wish TI would finally pick a decent usb device one of these days
  • [21:57:06] <geist> they always mess that part up
  • [22:01:04] * torus (n=nils@c170072.adsl.hansenet.de) Quit (Remote closed the connection)
  • [22:02:48] * feig (n=ejf3@cpe-66-67-149-163.rochester.res.rr.com) has joined #beagle
  • [22:18:36] * harper (n=harper@24-148-50-204.stk-ubr1.chi-stk.il.cable.rcn.com) has joined #beagle
  • [22:19:58] * feig1 (n=ejf3@cpe-66-67-149-163.rochester.res.rr.com) has joined #beagle
  • [22:23:17] * feig (n=ejf3@cpe-66-67-149-163.rochester.res.rr.com) Quit (Read error: 104 (Connection reset by peer))
  • [22:24:14] * JoeyBorn (n=jborn@adsl-75-3-4-165.dsl.chcgil.sbcglobal.net) has joined #beagle
  • [22:26:29] * [X]Spot (n=stancho@78.90.115.116) Quit (Read error: 110 (Connection timed out))
  • [22:35:57] * dcordes_ (n=dcordes@unaffiliated/dcordes) has joined #beagle
  • [22:45:07] * feig1 (n=ejf3@cpe-66-67-149-163.rochester.res.rr.com) Quit (Read error: 110 (Connection timed out))
  • [22:48:36] * torus (n=nils@c170072.adsl.hansenet.de) has joined #beagle
  • [22:53:12] * dcordes (n=dcordes@unaffiliated/dcordes) Quit (Read error: 110 (Connection timed out))
  • [23:04:54] * dcordes_ (n=dcordes@unaffiliated/dcordes) Quit ("leaving")
  • [23:25:57] * harper (n=harper@24-148-50-204.stk-ubr1.chi-stk.il.cable.rcn.com) Quit (Read error: 110 (Connection timed out))
  • [23:31:13] * guillaum1 (n=Guillaum@AMontsouris-153-1-28-4.w86-212.abo.wanadoo.fr) Quit ("Leaving.")
  • [23:31:44] * guillaum1 (n=gl@AMontsouris-153-1-28-4.w86-212.abo.wanadoo.fr) has joined #beagle
  • [23:37:24] * torus (n=nils@c170072.adsl.hansenet.de) Quit (Remote closed the connection)
  • [23:51:18] * felipec (n=felipec@a88-113-6-167.elisa-laajakaista.fi) Quit ("Leaving")
  • [23:56:47] * dcordes (n=dcordes@unaffiliated/dcordes) has joined #beagle
  • [23:58:31] * GAN800 (n=ryan@pdpc/supporter/active/generalantilles) has joined #beagle